2 Axial Portable Telescopic Mast
This mast is designed for sport fans and photographers.
This mast usually has pin locking or hand wheel brake structure. It
supports by tripod, the tripod is freely nested, open , adjust the
support angle.
The mast also has two or three wheels which is easy to move on the
ground , reducing the labor intensity.
The mast can be stored in a canvas bag when it is not used.
This mast has three nylon guy lines and three ground stake which
improves the mast stability when it is windy.
product introduction:
Telescoping mast is a mast comprised of sections which collapse
into each other.
Our best-selling mast pole is made of the highest quality aluminum
and built to last.
Extremely portable but ready to provide years of permanent service
too!
Available in extensions from 3m up to 15m.
specification:
Hard push up
| extended height (m) | No. Of section | Retracted height(m) | Outer tube range(mm) | Self weight (kg) | Max.payload (kg) |
| 3 | 2 | 1.55 | 50-55 | 3 | 20 |
| 4 | 3 | 1.35 | 50-60 | 4 | 20 |
| 5 | 3 | 1.7 | 50-60 | 5 | 20 |
| 6 | 4 | 1.55 | 45-60 | 6.5 | 15 |
| 7 | 4 | 1.8 | 45-60 | 7 | 15 |
| 8 | 5 | 1.65 | 45-65 | 9 | 12 |
| 9 | 5 | 1.85 | 45-65 | 10 | 12 |
| 10 | 6 | 1.7 | 40-65 | 12 | 10 |
| 12 | 7 | 1.75 | 35-65 | 28 | 8 |
| 15 | 8 | 1.9 | 30-65 | | 6 |
Product photo:
Application areas:
For WiFi, Portable Antennas, Elevated Photos
Ideal for:Emergency Response Antenna Systems, Restricted Space
Antennas - Prepping Systems
Elevated Photography - Weather Instruments - WiFi Site Surveying -
End Zone Cameras
Accessories:
Usually these masts require a flat or socket wrench, with the quick
release clamps you can raise and lower the masts without any tools.
Even with limited space these quick clamps can be easily used,
because the lever can be adjusted at any position. Just pull out
and release the lever, the strong spring latches the lever at the
desired position.
Attentions:
The mast can be extended to any length and securely locks into
place by means of a massive clamp. The maximum allowed extended
length is marked by a color ring approx. 20cm before the end of
each tube. There is no fixed stop which makes it advisable to
approach the marking slowly when extending the telescopes.
These masts are ideally suited for portable applications due to the
low weight and the telescopic mechanism. When setting up the mast
please pay special attention to the clamping length; the clamping
length of the mast must be at least 1/6th of the extended length,
or at least 1 meter at the minimum. When extending the mast more
than 6 meters measured from the uppermost clamping point additional
guys are mandatory.
The tubes are made of weather-proof aluminum alloy. The tubes are
tapered by 5 mm and the tube thickness is 2mm. Please refer to the
following table for weight and dimensions. The stated additional
forces refer to a horizontally applied force at the tip of the
extended mast - without guys and a mast clamping length of 1/6th.
The calculation includes the inherent load at a wind speed of
50km/h (which is equivalent to a wind force of 7).
also we can produce according to clients special requests, and can
give proposals.
Packing, delivery tiem, and shipping:
We will close then pack the goods safely in solid wooden box.
Prodcution lead time for sample: 2 weeks; 4 weeks for bulk order
Ship by sea, air, or express according to your request.
